Cobra SS-i Oversize Irons Specifications
Full factory loft, lie and length chart for the Cobra SS-i Oversize irons, 2003–2004.
- Years produced
- 2003–2004
- Category
- Game Improvement Irons
- Construction
- investment cast oversize cavity back
- Material
- 431 stainless steel with urethane cavity insert
- Set makeup
- 2–LW
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) |
|---|---|---|---|
| 2 | 18 | 60 | 39.5 |
| 3 | 20 | 60.5 | 39 |
| 4 | 23 | 61 | 38.5 |
| 5 | 26 | 61.5 | 38 |
| 6 | 29 | 62 | 37.5 |
| 7 | 33 | 62.5 | 37 |
| 8 | 37 | 63 | 36.5 |
| 9 | 41 | 63.5 | 36 |
| PW | 45 | 64 | 35.75 |
| GW | 50 | 64 | 35.5 |
| SW | 55 | 64 | 35.25 |
| LW | 60 | 64 | 35.25 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Cobra SS-i Oversize
The King Cobra SS-i Oversize is Cobra's 2003 oversize game-improvement iron, investment cast in a comparatively soft 431 stainless steel with a deep undercut cavity filled with a urethane insert to damp vibration. Despite the "SS-i" name sometimes being grouped with Cobra's forged clubs, this is the cast oversize model — Cobra sold a separate King Cobra SS Forged set alongside it, with different lofts. Lofts are traditional by modern standards: the 7-iron is 33 degrees and the pitching wedge 45 degrees, on a 37.00-inch steel 7-iron. The numbered set ran 2-iron through pitching wedge, with three matching wedges that Cobra listed by loft rather than by letter (50, 55 and 60 degrees), shown here as GW, SW and LW. Specs below are the men's steel-shaft values from Cobra's own archived spec table; graphite builds were half an inch longer throughout. Cobra published an offset column for this set, but its values run backwards relative to normal convention (increasing toward the wedges), so they are not reproduced here.
Related models
- Later Cobra game-improvement iron: S3
- Compare: Cobra SS-i Oversize vs Cobra King Cobra SS Oversize
- Compare: Cobra SS-i Oversize vs Cobra S3
Frequently asked questions
What is the loft of a Cobra SS-i 7-iron?
The Cobra King Cobra SS-i Oversize 7-iron has a loft of 33 degrees, a lie of 62.5 degrees and a steel-shaft length of 37.00 inches.
Is the Cobra SS-i a forged iron?
No. The SS-i Oversize is investment cast from 431 stainless steel. Cobra sold a separate King Cobra SS Forged set at the same time, which had different lofts.
What wedges came with the Cobra SS-i set?
Cobra listed the SS-i wedges by loft rather than by letter: 50, 55 and 60 degrees, alongside a 45-degree pitching wedge.
Finding a used set
The Cobra SS-i Oversize is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- Cobra Golf official 'COBRA IRON SPECIFICATIONS' page (cobragolf.com/irons/specs.asp), archived 2004-02-21 via web.archive.org — retrieved directly; the 'King Cobra Men's SS-i Oversize' block supplies loft, lie, offset, swing weight and both graphite and steel lengths for the 2-iron through the 60-degree wedge
- Head material (431 stainless), undercut cavity and urethane insert corroborated by retailer and review descriptions (2nd Swing, golfreview.com user reviews); 2003 introduction date corroborated by Cobra brand histories citing the Golf Datatech year-end report
Last reviewed 2026-07-22. Spot an error? [email protected]