Wilson Staff Di11 Irons Specifications
Full factory loft, lie and length chart for the Wilson Staff Di11 irons, 2010–2013.
- Years produced
- 2010–2013
- Category
- Game Improvement Irons
- Construction
- cast cavity back
- Material
- stainless steel
- Set makeup
- 3–SW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) |
|---|---|---|---|
| 3 | 18 | 59.5 | 39.5 |
| 4 | 22 | 60 | 39 |
| 5 | 25 | 61 | 38.5 |
| 6 | 29 | 61.5 | 38 |
| 7 | 32 | 62 | 37.5 |
| 8 | 36 | 63 | 37 |
| 9 | 39 | 63.5 | 36.5 |
| PW | 43 | 64 | 36 |
| GW | 46 | 64 | 36 |
| SW | 55 | 64 | 36 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Wilson Staff Di11
The Di11 closed out Wilson Staff's Di distance line in 2010, built around what Wilson called the largest sweet spot of any iron it had made: weight stripped from the face perimeter and cavity leaves a large unsupported face, with mass moved low for launch and rearward for stability. Reviewers classed it at the most forgiving end of game improvement, and its spec sheet is unconventional — a 46-degree gap wedge sits only three degrees under the pitching wedge, leaving a nine-degree jump to the sand wedge.
Stock shafts
- True Temper wide-tip steel — steel · flexes: Uniflex
- UST Proforce 65 (wide tip) — graphite
Related models
- Predecessor: Wilson Staff Di9
- Successor distance line: Wilson Staff D100
- Control-line sibling: Wilson Staff Ci11
- Compare: Wilson Staff Di11 vs Wilson Staff Di9
- Compare: Wilson Staff Di11 vs Wilson Staff D100
- Compare: Wilson Staff Di11 vs Wilson Staff Ci11
Frequently asked questions
What is the loft of a Wilson Staff Di11 7-iron?
The Wilson Staff Di11 7-iron has a loft of 32 degrees, a lie of 62 degrees and a steel-shaft length of 37.5 inches.
Are the Wilson Di11 irons forgiving?
Yes — Wilson claimed the largest sweet spot of any iron it had produced, and reviewers placed the Di11 at the super-game-improvement end of the spectrum.
Why is the Di11 gap wedge only 46 degrees?
Wilson published a 43-degree pitching wedge and 46-degree gap wedge, an unusually tight 3-degree gap that leaves 9 degrees to the 55-degree sand wedge; players wanting even gapping often bent the GW weaker or added a wedge.
Finding a used set
The Wilson Staff Di11 ran from 2010 to 2013 and is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- 2nd Swing Golf specification table for the Wilson Staff Di11 single irons (https://www.2ndswing.com/golf-clubs/single-irons/wilson-staff-staff-di11-single-iron) — supplied every loft, lie and length above and the UST Proforce 65 graphite stock shaft; the 46-degree GW and 55-degree SW gapping is as published
- GolfWRX Wilson Staff Di11 editor review and Golfmagic 'Wilson Staff release Di11 range' — 2010-2011 model window, largest-sweet-spot design story with weight pulled low and back, and the note that lofts and lengths are nontraditional even for the distance class
- Today's Golfer classes the Di11 as a super-game-improvement iron; it is filed here as game improvement, the top of that range
- Offset, bounce and swing weight were not published and are omitted; confidence is medium
Last reviewed 2026-07-29. Spot an error? [email protected]