Ping G25 Irons Specifications
Full factory loft, lie and length chart for the Ping G25 irons, 2013–2014.
- Years produced
- 2013–2014
- Category
- Game Improvement Irons
- Construction
- investment cast
- Material
- 17-4 stainless steel
- Set makeup
- 3–LW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Bounce | Swing wt |
|---|---|---|---|---|---|
| 3 | 20 | 59.25 | 38.75 | 0 | D0 |
| 4 | 23 | 60 | 38.25 | 1 | D0 |
| 5 | 26 | 60.75 | 37.75 | 3 | D0 |
| 6 | 29 | 61.5 | 37.25 | 5 | D0 |
| 7 | 32 | 62.25 | 36.75 | 7 | D0 |
| 8 | 36 | 63 | 36.25 | 9 | D0 |
| 9 | 40 | 63.75 | 35.75 | 10 | D0 |
| PW | 45 | 64 | 35.5 | 11 | D2 |
| UW | 50 | 64 | 35.5 | 11 | D2 |
| SW | 54 | 64.25 | 35.25 | 12 | D4 |
| LW | 58 | 64.5 | 35 | 12 | D6 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Ping G25
The G25 refined the G-series formula with a Custom Tuning Port and progressive geometry: wider soles and more offset in the long irons for higher launch, thinner soles and less offset in the scoring clubs for control. Lofts are identical to the 2009 G15 through the set, with the 7-iron at 32 degrees, but bounce was softened in the long irons (the 3-iron moved from -2 to 0 degrees). Ping's colour-code (dot) system sets lie angle relative to standard: gold 4 flat, brown 3 flat, orange 2 flat, red 1 flat, BLACK standard, blue 1 upright, green 2 upright, white 3 upright, silver 4 upright, maroon 5 upright. The lies below are the BLACK (standard) lies.
Stock shafts
- Ping CFS — steel · 94-114g · flexes: SR, R, S, X
- Ping TFC 189I — graphite · 70-86g · flexes: SR, R, S
Related models
- Earlier G-series iron: Ping G15
- First G-series iron: Ping G2
- Compare: Ping G25 vs Ping G15
- Compare: Ping G25 vs Ping G20
- Compare: Ping G25 vs Ping G30
- Compare: Ping G25 vs Ping G2
- Compare: Ping G25 vs Ping S55
Frequently asked questions
What is the loft of a Ping G25 7-iron?
The Ping G25 7-iron has a loft of 32 degrees, a standard (black dot) lie of 62.25 degrees and a steel-shaft length of 36.75 inches.
Are Ping G25 lofts stronger than the G15?
No — the two sets share identical lofts, lies and lengths through the bag. The G25 differs mainly in sole width, offset profile and bounce, which was reduced in the long irons.
What shafts came stock in the Ping G25 irons?
Ping CFS steel in SR, R, S and X flexes (94-114 grams) or Ping TFC 189I graphite in SR, R and S flexes (70-86 grams).
Finding a used set
The Ping G25 is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- qsponge.com Ping G25 iron table (loft, lie, length, bounce and swing weight for 3-iron through LW)
- golfstorageguide.com PING G25 irons spec chart, corroborating the 7-iron (32 / 62.25 / 36.750 / 7.0) and the UW, SW and LW rows
- GolfWorks Ping shaft replacement reference PDF (2013 G25 Irons — CFS steel SR/R/S/X 94-114g; TFC 189I graphite SR/R/S 70-86g)
- TGW / PGA Tour Superstore Ping colour code chart guides (black dot = standard lie)
- Note: per-club offset values were not found in a reliable published source and are omitted.
- Note: one reading of the archived G25 chart takes its final column as sole width rather than bounce angle. The values are recorded here as bounce because they run 0-12 in whole degrees and track the G20 and G30 bounce progressions closely; as a sole width in inches they would be implausible. Treat the column as bounce angle pending a cleaner scan of the original chart.
Last reviewed 2026-07-22. Spot an error? [email protected]