Ping G710 Irons Specifications
Full factory loft, lie and length chart for the Ping G710 irons, 2020–2024.
- Years produced
- 2020–2024
- Category
- Super Game Improvement Irons
- Construction
- hollow body with a maraging steel face
- Material
- maraging C300 steel face plasma-welded to a 17-4 stainless body, with tungsten toe and hosel weights
- Set makeup
- 4–SW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Offset (in) | Swing wt |
|---|---|---|---|---|---|
| 4 | 20 | 60.5 | 38.875 | 0.29 | C9 |
| 5 | 23 | 61 | 38.25 | 0.26 | C9 |
| 6 | 26 | 61.5 | 37.625 | 0.23 | C9 |
| 7 | 29.5 | 62 | 37 | 0.2 | C9 |
| 8 | 34 | 62.8 | 36.5 | 0.18 | C9 |
| 9 | 39 | 63.5 | 36 | 0.16 | C9.5 |
| PW | 44 | 64.1 | 35.5 | 0.13 | D1 |
| UW | 49 | 64.1 | 35.5 | 0.11 | D1 |
| SW | 54 | 64.4 | 35.25 | 0.09 | D2 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
Shop Ping G710
Compare prices for new and used sets on eBay:
We may earn a commission from purchases made through links on this page at no extra cost to you.
Loft progression
About the Ping G710
The G710 is the second generation of Ping's hollow-body distance iron and carries the G700's loft, lie, length and offset chart over unchanged — a 29.5-degree 7-iron at 37.00 inches. What changed is the mass: tungsten toe and hosel weights push the moment of inertia about 5 per cent above the G700, the maraging face is machined rather than only plasma-welded, and the body gets a hydropearl chrome finish. Lies below are the black (standard) code.
Stock shafts
- Ping AWT 2.0 — steel
- True Temper Elevate MPH 95 — steel
- Ping Alta CB Red — graphite
- Ping Alta Distanza Black — graphite
Related models
Frequently asked questions
What is the loft of a Ping G710 7-iron?
The Ping G710 7-iron has a loft of 29.5 degrees, a standard (black dot) lie of 62.0 degrees and a steel-shaft length of 37.00 inches.
When were Ping G710 irons made?
The G710 arrived in 2020, following the G700, and was replaced by the G730 in 2024.
Are Ping G700 and G710 lofts the same?
Yes. Both run 20, 23, 26, 29.5, 34, 39, 44, 49 and 54 degrees from 4-iron to sand wedge, at the same lies, lengths and offsets. The G710's gains come from tungsten toe and hosel weighting and a machined face, not from stronger lofts.
What is the pitching wedge loft on the Ping G710?
44 degrees, with a 49-degree utility wedge and a 54-degree sand wedge completing the set.
Finding a used set
The Ping G710 ran from 2020 to 2024 and is no longer in production, so the used market is the only source. Search the used listings on eBay, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- 2ndswing.com Ping G710 Iron Set specification table — loft, lie, length, offset and swing weight for the 4-iron through sand wedge, and the AWT 2.0 stock shaft.
- golfalot.com and todays-golfer.com G710 reviews — confirm the 29.5-degree 7-iron, the 4-iron-to-SW set range, the tungsten toe and hosel weights, the machined maraging face, the roughly 5 per cent MOI gain over the G700, and the 2020 launch.
- Note on the chart: the G710 table published by 2ndswing is identical to its G700 table in every column. That matches Ping's positioning of the G710 as a same-spec mass-properties update, and the 7-iron loft is independently corroborated, but no Ping spec sheet was located, so confidence is medium.
Last updated 28 July 2026. Spot an error? info@loftchart.com