Wilson Staff Model Blade Irons Specifications
Full factory loft, lie and length chart for the Wilson Staff Model Blade irons, 2019–present.
- Years produced
- 2019–present
- Category
- Blade / Muscleback
- Construction
- forged
- Material
- soft-forged 8620 carbon steel, precision milled
- Set makeup
- 2–PW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Swing wt |
|---|---|---|---|---|
| 2 | 18 | 59 | 39.75 | D2 |
| 3 | 20 | 59.5 | 39.25 | D2 |
| 4 | 23 | 60 | 38.75 | D2 |
| 5 | 26 | 61 | 38.25 | D2 |
| 6 | 30 | 61.5 | 37.75 | D2 |
| 7 | 34 | 62 | 37.25 | D2 |
| 8 | 38 | 63 | 36.75 | D2 |
| 9 | 42 | 63.5 | 36.25 | D2 |
| PW | 46 | 64 | 35.75 | D2 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Wilson Staff Model Blade
The Staff Model Blade is Wilson's muscle-back tour iron, unveiled in January 2019 after prototype versions were played on tour and carried forward through later refreshes alongside the Staff Model CB cavity back. Heads are soft-forged from 8620 carbon steel and then precision milled, with a compact profile, minimal offset and Wilson's Fluid Feel Hosel, which removes mass from the hosel to allow a slightly larger head and wider sole. Lofts are traditional, with a 34-degree 7-iron and a 46-degree pitching wedge, matching the Staff Model CB through the set. Clubs are built from 2-iron through pitching wedge, with 3-PW and 4-PW the usual stock sets. Figures below are the standard men's steel-shaft specification.
Related models
- Companion cavity back: Wilson Staff Model CB
- Predecessor: Wilson Staff FG Tour 100
- Compare: Wilson Staff Model Blade vs Wilson Staff FG Tour 100
- Compare: Wilson Staff Model Blade vs Wilson Staff Model CB
Frequently asked questions
What is the loft of a Wilson Staff Model Blade 7-iron?
The Wilson Staff Model Blade 7-iron has a loft of 34 degrees, with a 62-degree lie and a 37.25-inch steel-shaft length.
What clubs come in a Wilson Staff Model Blade set?
The Blade is built from 2-iron through pitching wedge, and is normally sold as a 3-PW or 4-PW set. There is no gap wedge in the blade range.
Do the Staff Model Blade and Staff Model CB share lofts?
Yes. Both run 18 degrees at the 2-iron to 46 degrees at the pitching wedge with the same lengths, so the two can be combined in a mixed set. Only the CB adds a 50-degree gap wedge.
Finding a used set
The Wilson Staff Model Blade is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- 2nd Swing Golf 'Wilson Staff Staff Model Blade Iron Set' specification table (club, loft, length, lie, swing weight, 2-iron through PW) and its 3-PW / 4-PW set listings — retrieved July 2026. Retailer-published table, not a Wilson spec sheet.
- Today's Golfer, January 2019, 'Wilson reveal new Staff Model blade irons' — reveal date and the tour-prototype background. Note the model is often grouped with the 2020 Staff Model CB as Wilson's players line, but the Blade itself was launched a year earlier.
- Plugged In Golf 'Wilson Staff Model Blades Irons Review' (2019) — Fluid Feel Hosel, soft-forged 8620 carbon steel construction and milled finishing. That review also notes Wilson did not publish bounce specs, so bounce is omitted here. Offset is omitted because available listings disagreed on it.
Last reviewed 2026-07-22. Spot an error? [email protected]