Cleveland Launcher Irons Specifications
Full factory loft, lie and length chart for the Cleveland Launcher irons, 2005–2010.
- Years produced
- 2005–2010
- Category
- Game Improvement Irons
- Construction
- —
- Material
- —
- Set makeup
- 3–DW
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Swing wt |
|---|---|---|---|---|
| 3 | 20.5 | 60 | 39.375 | D1 |
| 4 | 23 | 60.5 | 38.75 | D1 |
| 5 | 26 | 61 | 38.125 | D1 |
| 6 | 29 | 61.5 | 37.5 | D2 |
| 7 | 33 | 62.5 | 37 | D2 |
| 8 | 37 | 63 | 36.5 | D2 |
| 9 | 41 | 64 | 36 | D2 |
| PW | 45 | 64.5 | 35.5 | D3 |
| SW | 55 | 65 | 35 | D5 |
| DW | 50 | 65 | 35.25 | D4 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Cleveland Launcher
The Launcher irons are an oversize game-improvement set built around a split design: the 3, 4 and 5 are hybrid-style heads with the largest face in the set and a parabolic leading edge, while the 6 through sand wedge are conventional oversize iron heads with a thick topline and extra offset. Both halves use Cleveland's extended horseshoe perimeter weighting, which the company rated at 20 percent higher MOI than a traditional iron and up to 3,000 g-cm2 in the long irons. Lofts are moderately strong for the period at 33 degrees in the 7-iron and 45 degrees in the pitching wedge. The stock set ran 3-iron through sand wedge, including a 50-degree DW gap wedge and a 55-degree SW. The specs below are the standard men's steel-shaft numbers from Cleveland's own product page; graphite builds were a quarter inch longer at every club.
Stock shafts
- Cleveland Golf FlightSpeed Steel — steel · 117-120g · flexes: R, S
- Cleveland Golf FlightSpeed Graphite — graphite · 75-83g · flexes: A, R, S
Related models
- Contemporary Cleveland game-improvement iron: CG7
- Later Launcher-branded iron: Launcher HB
- Compare: Cleveland Launcher vs Cleveland CG7
- Compare: Cleveland Launcher vs Cleveland Launcher HB
Frequently asked questions
What is the loft of a Cleveland Launcher 7-iron?
The Cleveland Launcher 7-iron has a loft of 33 degrees, a lie of 62.5 degrees and a steel-shaft length of 37 inches.
What are the Cleveland Launcher wedge lofts?
The pitching wedge is 45 degrees, the DW gap wedge 50 degrees and the sand wedge 55 degrees.
Are the Cleveland Launcher long irons really hybrids?
The 3, 4 and 5 are hybrid-style heads built on an iron chassis with the largest face in the set and a parabolic leading edge, while the 6-iron through sand wedge are conventional oversize iron heads.
Finding a used set
The Cleveland Launcher is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- Cleveland Golf official LAUNCHER IRONS product page, archived 2010-03-16 via web.archive.org (http://web.archive.org/web/20100316122929/http://www.clevelandgolf.com/AA_launcher-irons__launcher_irons__viewProd_irons.html) — full IRON / LOFT / LIE / STEEL LENGTH / GRAPHITE LENGTH / STEEL SWING WEIGHT / GRAPHITE SWING WEIGHT table for 3h through SWi, plus the FlightSpeed steel and graphite stock shaft tables. Lengths on that page are given as fractions (39 3/8", 38 3/4", 38 1/8" and so on) and have been converted to decimal inches here.
- Same archived page for the design description (oversize face, parabolic leading edge on the 3-5, extended horseshoe perimeter weighting, 3,000 MOI figure).
- Note on dating: the spec table above was read from a 2010 snapshot, which is the earliest archived Cleveland page carrying the Launcher iron spec table. The 2005 introduction year is not established by that document.
Last reviewed 2026-07-22. Spot an error? [email protected]