Mizuno MP-60 Irons Specifications
Full factory loft, lie and length chart for the Mizuno MP-60 irons, 2006–2008.
- Years produced
- 2006–2008
- Category
- Players Irons
- Construction
- forged
- Material
- 1025E mild carbon steel
- Set makeup
- 2–PW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Offset (in) | Bounce |
|---|---|---|---|---|---|
| 2 | 18 | 59 | 39.25 | 0.154 | 2 |
| 3 | 21 | 59.5 | 38.75 | 0.142 | 2 |
| 4 | 24 | 60 | 38.25 | 0.134 | 2 |
| 5 | 27 | 60.5 | 37.75 | 0.134 | 2 |
| 6 | 31 | 61 | 37.25 | 0.13 | 3 |
| 7 | 35 | 61.5 | 36.75 | 0.126 | 3 |
| 8 | 39 | 62 | 36.25 | 0.126 | 4 |
| 9 | 43 | 62.5 | 35.75 | 0.114 | 5 |
| PW | 47 | 63 | 35.5 | 0.114 | 6 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Mizuno MP-60
The MP-60 is a Grain Flow Forged cavity back built on Mizuno's Cut Muscle design, in which a reinforcing pad sits behind a cavity rather than filling it. Mizuno described the head as about 4 percent larger than the MP-32 it was drawn from, with a correspondingly larger hitting area and slightly more offset. Lofts follow the traditional MP progression, with a 35-degree 7-iron and a 47-degree pitching wedge. The set was sold 3-PW with a 2-iron available; lengths and lofts listed are the standard men's steel-shaft specification.
Stock shafts
- True Temper Dynamic Gold — steel
Related models
- Design the MP-60 was drawn from: Mizuno MP-32
- Successor: Mizuno MP-52
- Compare: Mizuno MP-60 vs Mizuno MP-52
- Compare: Mizuno MP-60 vs Mizuno MP-32
Frequently asked questions
What is the loft of a Mizuno MP-60 7-iron?
The Mizuno MP-60 7-iron has a loft of 35 degrees, with a 61.5-degree lie and a 36.75-inch steel-shaft length.
What year did the Mizuno MP-60 come out?
The MP-60 was introduced in 2006 and was replaced by the MP-52 the following year. It is often mislabelled as a 2011 model because it shares a spec chart layout with later MP irons.
How does the MP-60 differ from the MP-32?
The MP-60 uses the same Cut Muscle idea but on a head Mizuno rated as roughly 4 percent larger, and it carries more offset - 0.126 inches at the 7-iron against 0.110 inches on the MP-32 - while keeping identical lofts and lies.
Finding a used set
The Mizuno MP-60 is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- golfclubspec.com iron specification database, Mizuno MP-60 entry dated 2006 (loft, lie, length, offset, bounce for 2-iron through pitching wedge)
- qsponge.com Mizuno MP-60 loft table, corroborating the 18-47 degree loft range and 59.0-63.0 degree lie progression
- golfbluebook.com Mizuno MP-60 research page for the Grain Flow Forged 1025 mild carbon steel Cut Muscle construction and the head being 4 percent larger than the MP-32
- Note: the golfclubspec table prints the pitching wedge loft as 37 degrees, which is a transcription error; 47 degrees is used here, matching every other MP-60 source.
- Note: year_discontinued is taken as the year the successor model was introduced.
- Note: year_discontinued follows the successor's introduction year, and the MP-52 is now correctly dated to 30 September 2008 rather than 2007; this figure moves from 2007 to 2008 to match. No dated announcement or retail source was located for the MP-60's own introduction, so year_introduced is left at 2006 on secondary sourcing and should be treated as approximate.
Last reviewed 2026-07-22. Spot an error? [email protected]