Ping i15 Irons Specifications
Full factory loft, lie and length chart for the Ping i15 irons, 2009–2012.
- Years produced
- 2009–2012
- Category
- Players Irons
- Construction
- investment cast
- Material
- 17-4 stainless steel
- Set makeup
- 3–UW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Offset (in) | Bounce | Swing wt |
|---|---|---|---|---|---|---|
| 3 | 21 | 59.25 | 38.75 | 0.26 | -2.7 | D0 |
| 4 | 24 | 60 | 38.25 | 0.22 | -1.8 | D0 |
| 5 | 27 | 60.75 | 37.75 | 0.19 | 0.8 | D0 |
| 6 | 30 | 61.5 | 37.25 | 0.17 | 2.8 | D0 |
| 7 | 33 | 62.25 | 36.75 | 0.14 | 5 | D0 |
| 8 | 37 | 63 | 36.25 | 0.11 | 6 | D0 |
| 9 | 41 | 63.75 | 35.75 | 0.09 | 8 | D0 |
| PW | 46 | 64 | 35.5 | 0.07 | 9 | D2 |
| UW | 50 | 64 | 35.5 | — | 10 | D2 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Ping i15
Launched alongside the G15 in the autumn of 2009, the i15 is the tour-shaped half of that pair: a smaller cast head with a machined face, a thinner top line and a tungsten toe weight. Lofts step back from the i10 through the mid and short irons — 33 degrees at the 7-iron against 34, 41 at the 9-iron against 42 — while the lie, length and bounce chart carries over. The long irons run negative bounce, minus 2.7 degrees at the 3-iron. Lies below are the black (standard) colour code.
Stock shafts
- Ping AWT — steel · flexes: Soft R, R, S, X
- Ping Z-Z65 — steel
- Ping TFC 149i — graphite · flexes: L, Soft R, R, S
Related models
- Predecessor: Ping i10
- Successor: Ping i20
- Game-improvement sibling: Ping G15
- Compare: Ping i15 vs Ping i10
- Compare: Ping i15 vs Ping G15
Frequently asked questions
What is the loft of a Ping i15 7-iron?
The Ping i15 7-iron has a loft of 33 degrees, a standard (black dot) lie of 62.25 degrees and a steel-shaft length of 36.75 inches.
When were Ping i15 irons made?
The i15 launched in 2009 alongside the G15 and was replaced by the i20 in 2012.
Why do Ping i15 long irons have negative bounce?
The 3-iron and 4-iron are published at minus 2.7 and minus 1.8 degrees of bounce, meaning the leading edge sits below the trailing edge at address. It is a tour-style sole intended to cut into the turf rather than skid off it.
What is the difference between the Ping i15 and the i10?
Lie, length and offset geometry carry over, but the i15 weakens the mid and short irons by a degree — 33 degrees at the 7-iron against the i10's 34 — and adds a machined face and a tungsten toe weight.
Finding a used set
The Ping i15 ran from 2009 to 2012 and is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- thesandtrap.com 'PING i15 Irons Review' (published 20 November 2009) — the full loft, lie, length, offset, bounce and swing-weight table for the 3-iron to pitching wedge, plus the AWT / TFC 149i stock shaft list.
- golfclubspec.com Ping i15 entry (iron_results.php?id=277) — independently corroborates every loft, lie, length and offset above and adds the utility wedge row; it rounds bounce to whole degrees where the review gives tenths, and the review's finer figures are used here.
- golfmonthly.com 'PING i15 and PING G15 ranges launched' — dates the launch to 2009.
- Note: the utility wedge offset was not published by either source and is omitted rather than estimated.
Last reviewed 2026-07-28. Spot an error? [email protected]