TaylorMade SpeedBlade HL Irons Specifications

Full factory loft, lie and length chart for the TaylorMade SpeedBlade HL irons, 2014–2015.

Years produced: 2014–2015
Category: Game Improvement Irons
Construction: cast with a through-slot Speed Pocket, higher-lofted HL build
Material: cast stainless steel
Set makeup: 4–AW

Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.

Loft, lie & length chart

Standard men's steel-shaft specifications for the TaylorMade SpeedBlade HL irons.
Club	Loft (°)	Lie (°)	Length (in)	Offset (in)	Swing wt
4	21	61	38.875	0.228	D2.5
5	24	61.75	38.25	0.205	D2.5
6	27.5	62.5	37.625	0.177	D2.5
7	31.5	63	37	0.154	D2.5
8	35.5	63.5	36.5	0.122	D2.5
9	40.5	64	36	0.098	D2.5
PW	46	64.5	35.5	0.079	D2.5
AW	51	64.5	35.5	0.051	D2.5

Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.

About the TaylorMade SpeedBlade HL

The SpeedBlade HL is the high-launch companion to the 2013 SpeedBlade, sold from 2014 mainly as boxed 4-PW and 4-PW-plus-AW sets for players who need more height. Each head carries one degree more loft than the standard SpeedBlade — 31.5 degrees at the 7-iron against 30.5 — while lie, length and offset stay on the standard SpeedBlade ladder. The Speed Pocket sole slot and deep undercut cavity are unchanged from the standard model.

Stock shafts

TaylorMade SpeedBlade 85 — steel

Related models

Frequently asked questions

What is the loft of a TaylorMade SpeedBlade HL 7-iron?

The SpeedBlade HL 7-iron has a loft of 31.5 degrees — one degree weaker than the standard SpeedBlade — with a 63-degree lie and 37-inch length.

What is the difference between the SpeedBlade and SpeedBlade HL irons?

The HL (high launch) version adds one degree of loft to every head to make the set easier to flight, while lie angles, lengths and offsets are identical to the standard SpeedBlade.

What clubs came in the TaylorMade SpeedBlade HL set?

The HL was sold as boxed 4-PW and 4-PW plus 51-degree AW sets from 2014, in steel and graphite builds.

Finding a used set

The TaylorMade SpeedBlade HL ran from 2014 to 2015 and is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.

Data compiled from:

2nd Swing Golf specification table for the TaylorMade SpeedBlade HL iron set (https://www.2ndswing.com/golf-clubs/iron-sets/taylormade-speedblade-hl-iron-set) — supplied every loft, lie, length, offset and swing weight above; offsets published in millimetres (5.8 mm down to 1.3 mm) and converted to inches here.
Set composition: PGA Tour Superstore and GolfEtail retail listings sold the HL as 4-PW and 4-PW+AW sets, which is the range recorded here; 2nd Swing also lists a 3-iron (18 degrees) and 56/60-degree SW/LW columns that were not part of the normal retail set.
Note on the loft ladder: every HL club is exactly one degree weaker than the standard SpeedBlade as published on TaylorMade's own SpeedBlade spec sheet (SpeedBlade_Irons_SS.pdf), with lie, length and offset identical — consistent with TaylorMade's practice for HL variants. A conflicting spec table at intheholegolf.com (half-degree offsets, uniform half-inch lengths) does not match TaylorMade's published length ladder and was not used.
Note: bounce is omitted — no source carried a bounce column for the HL heads. Confidence is medium: the numbers come from a large used-club retailer rather than a manufacturer sheet.

Last reviewed 2026-07-29. Spot an error? [email protected]