Cobra KING TEC X (2024) Irons Specifications
Full factory loft, lie and length chart for the Cobra KING TEC X (2024) irons, from 2024.
- Years produced
- from 2024
- Category
- Players Distance Irons
- Construction
- hollow body with an internal tungsten weight
- Material
- steel hollow body with a 70-gram internal tungsten weight
- Set makeup
- 4–GW
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Offset (in) | Swing wt |
|---|---|---|---|---|---|
| 4 | 19 | 62 | 38.75 | 0.165 | D1 |
| 5 | 21 | 62.5 | 38.25 | 0.15 | D1 |
| 6 | 24 | 63 | 37.75 | 0.134 | D1 |
| 7 | 27 | 63.5 | 37.25 | 0.118 | D1 |
| 8 | 31.5 | 64 | 36.75 | 0.102 | D1 |
| 9 | 36.5 | 64.5 | 36.25 | 0.087 | D1 |
| PW | 42 | 65 | 36 | 0.071 | D2 |
| GW | 48 | 65 | 35.75 | 0.059 | D2 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
Loft progression
About the Cobra KING TEC X (2024)
The KING TEC X replaced the KING Forged Tec X in October 2024 as the larger and stronger-lofted of Cobra's two TEC irons, a hollow body with a 70-gram tungsten weight inside the head. The loft, lie and length chart is unchanged from the model it replaced: 27 degrees at the 7-iron and 42 at the pitching wedge, with lies one degree more upright than the KING TEC. The stock set is 5-iron to gap wedge in steel. A ONE Length version was sold alongside it; figures here are the variable-length men's right-handed steel build.
Stock shafts
- KBS Tour Lite — steel · 105 g · flexes: R, S
Related models
Frequently asked questions
What is the loft of a Cobra KING TEC X (2024) 7-iron?
The 2024 Cobra KING TEC X 7-iron has a loft of 27 degrees, a lie of 63.5 degrees and a steel-shaft length of 37.25 inches.
Did the lofts change from the KING Forged Tec X?
No. The 4-iron through gap wedge run 19, 21, 24, 27, 31.5, 36.5, 42 and 48 degrees on both.
Is the Cobra KING TEC X hollow?
Yes. Cobra describes a hollow body construction with an internal 70-gram tungsten weight.
What is the pitching wedge loft on the KING TEC X?
42 degrees, with a 48-degree gap wedge below it.
Production status
Introduced in 2024, the Cobra KING TEC X (2024) has no confirmed end date on file. It replaced the Cobra KING Forged Tec X. LoftChart records a discontinuation year only where a source dates it, and none has been found for this set, so it may or may not still be in the Cobra catalogue — check with Cobra or a retailer before counting on a new set. Used sets appear on eBay, 2nd Swing and Golf Avenue, and should be measured against the chart above before buying, since irons are routinely bent from standard.
- Cobra Golf's own KING TEC X Irons product page, stock specifications table (cobragolf.com, retrieved 29 September 2026) — supplied every loft, lie angle, offset, length and swing weight above for the 4-iron through gap wedge, the 5-GW stock steel set, the KBS Tour Lite stock shaft, and the hollow body with its 70-gram tungsten weight. Offsets are published in millimetres and converted to inches here.
- Announcement: Cobra published the KING TEC and KING TEC X on its store on 23 October 2024; launch coverage covers the KING TEC, KING TEC X and KING TEC X ONE Length together (golfwrx.com, golf.com).
- Status: no end date is recorded and the model is not marked as current. On 29 September 2026 Cobra still listed the KING TEC X, marked down to $999 from $1,299 and out of stock, and no replacement had been announced.
- Note: bounce is not published and is omitted rather than estimated.
Last updated 29 September 2026. Spot an error? info@loftchart.com