Honma TW747 P Irons Specifications
Full factory loft, lie and length chart for the Honma TW747 P irons, 2018–2020.
- Years produced
- 2018–2020
- Category
- Players Distance Irons
- Construction
- cast pocket cavity with tungsten sole weighting
- Material
- stainless steel with approximately 20 grams of tungsten in the sole
- Set makeup
- 4–SW
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Offset (in) |
|---|---|---|---|---|
| 4 | 19 | 60 | 38.5 | 0.118 |
| 5 | 21.5 | 60.5 | 38 | 0.118 |
| 6 | 25 | 61 | 37.5 | 0.098 |
| 7 | 28.5 | 61.5 | 37 | 0.098 |
| 8 | 33 | 62 | 36.5 | 0.079 |
| 9 | 38 | 62.5 | 36 | 0.079 |
| PW | 43.5 | 63 | 35.5 | 0.079 |
| GW | 48 | 63 | 35 | — |
| SW | 56 | 63.5 | 35 | — |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the Honma TW747 P
The TW747 P is the forgiving model in Honma's Tour World 747 line, but it is built around a compact head rather than an oversized one: the hosel is shortened to free mass, and roughly 20 grams of tungsten sits in the sole behind a pocket cavity to drop the centre of gravity. Offset is minimal and the top line is narrow. Honma numbers the wedges as 10 and 11 rather than PW and GW; those are recorded below as PW and GW. Two stock lengths are published, one for the VIZARD graphite build and one a quarter inch shorter for the N.S. Pro 950GH steel build — the steel figures are used here.
Stock shafts
- Honma VIZARD For TW747 50 — graphite
- Nippon N.S. Pro 950GH — steel
Related models
- Successor: Honma TR20 P
- Honma's distance iron of the following generation: Honma TR21 X
- Compare: Honma TW747 P vs Honma TR20 P
- Compare: Honma TW747 P vs Honma TR21 X
- Compare: Honma TW747 P vs Honma TW747 V
- Compare: Honma TW747 P vs Honma TW747 Vx
- Compare: Honma TW747 P vs Honma TW757 P
Frequently asked questions
What is the loft of a Honma TW747 P 7-iron?
The Honma TW747 P 7-iron has a loft of 28.5 degrees, a lie of 61.5 degrees and a steel-shaft length of 37.00 inches.
Why are Honma irons numbered up to 11?
Honma labels its wedges by continuing the iron numbering: the 10-iron is the pitching wedge at 43.5 degrees and the 11-iron the gap wedge at 48 degrees.
Do Honma TW747 P lengths depend on the shaft?
Yes. Honma publishes two length columns — the VIZARD graphite build runs a quarter inch longer than the N.S. Pro 950GH steel build at every club. The steel figures are the ones recorded here.
When were Honma TW747 P irons made?
Honma announced the Tour World 747 range in 2018 for the 2019 season, and replaced the P model with the TR20 P in 2020.
Finding a used set
The Honma TW747 P ran from 2018 to 2020 and is no longer in production, so the used market is the only source. Search eBay, 2nd Swing, Golf Avenue and the PGA Tour Superstore trade-in listings, and check the loft and lie against the chart above before buying — sets this age have often been bent from standard.
- honmagolf.com Tour World TW747 P product detail page (https://honmagolf.com/sea/product-details/1566) — loft, lie, offset (in millimetres) and both published length columns for the #4 through #11 and sand wedge, plus the VIZARD For TW747 50 and N.S. Pro 950GH stock shafts. Offset is converted to inches here and the steel-shaft length column is used, per this database's convention.
- golfalot.com 'Honma Tour World TW747 P Irons Review' and tourspecgolf.com "Honma's New 2019 TW747P Irons" — corroborate the 19-degree 4-iron, the 28.5-degree 7-iron and the 43.5-degree pitching wedge, the shortened hosel, the roughly 20 grams of tungsten in the sole, and the 2018 announcement for the 2019 season.
- Note: bounce and swing weight were not published on the product page and are omitted rather than estimated. Offset was not published for the #11 and sand wedge.
Last reviewed 2026-07-28. Spot an error? [email protected]