TaylorMade P7CB Irons Specifications
Full factory loft, lie and length chart for the TaylorMade P7CB irons, 2024–present.
- Years produced
- 2024–present
- Category
- Players Irons
- Construction
- forged with co-forged tungsten
- Material
- 1025 carbon steel
- Set makeup
- 3–GW
Data confidence: medium. These figures are compiled from secondary sources rather than a manufacturer spec sheet. If you have an original catalogue page, send it over and we will update the chart.
Loft, lie & length chart
| Club | Loft (°) | Lie (°) | Length (in) | Swing wt |
|---|---|---|---|---|
| 3 | 20 | 60.5 | 39 | D3 |
| 4 | 23 | 61 | 38.5 | D3 |
| 5 | 26 | 61.5 | 38 | D3 |
| 6 | 29 | 62 | 37.5 | D3 |
| 7 | 33 | 62.5 | 37 | D3 |
| 8 | 37 | 63 | 36.5 | D3 |
| 9 | 41 | 63.5 | 36 | D3 |
| PW | 46 | 64 | 35.75 | D4 |
| GW | 51 | 64 | 35.5 | D4 |
Lofts and lies are the factory standard build. Individual clubs may differ if they have been bent, re-shafted or re-gripped during their life.
About the TaylorMade P7CB
The P7CB is a compact tour cavity back, forged from 1025 carbon steel under what TaylorMade calls Compact Grain Forging at 2,000 tons, with a milled face and grooves. Co-forged tungsten in the perimeter holds the centre of gravity constant through the set rather than moving it, which is the opposite of the progressive-CG approach in the P790 and P770. Lofts are traditional for the category — 33 degrees at the 7-iron and 46 at the pitching wedge. Figures are the men's standard right-handed steel build.
Stock shafts
- True Temper Dynamic Gold Mid 115 — steel
Related models
- Cavity-back predecessor in the P7 line: TaylorMade P7MC
- Muscleback sibling: TaylorMade P7MB
- Hollow-body alternative: TaylorMade P770 (2023)
- Compare: TaylorMade P7CB vs TaylorMade P770 (2025)
- Compare: TaylorMade P7CB vs TaylorMade P7MC
- Compare: TaylorMade P7CB vs TaylorMade P7MB
- Compare: TaylorMade P7CB vs TaylorMade P770 (2023)
Frequently asked questions
What is the loft of a TaylorMade P7CB 7-iron?
The TaylorMade P7CB 7-iron has a loft of 33 degrees, a lie of 62.5 degrees and a steel-shaft length of 37.00 inches.
When did the TaylorMade P7CB come out?
2024, as the forged cavity back in the P7 tour line alongside the P7MB muscleback.
What is the difference between the P7CB and the P7MC?
Both are forged tour cavity backs. The P7CB uses co-forged tungsten in the perimeter to hold the centre of gravity constant through the set and is forged under 2,000 tons of pressure with a milled face and grooves.
What is the pitching wedge loft on the TaylorMade P7CB?
46 degrees, with a 51-degree gap wedge available below it.
Where it sits in the lineup
Introduced in 2024, the TaylorMade P7CB is a current players set in the TaylorMade range, with no replacement announced. New sets are built to the standard lofts, lies and lengths in the chart above, though a fitting can move any of them — so confirm the numbers on the order sheet. Used sets appear on eBay, 2nd Swing and Golf Avenue, and should be measured against this chart before buying.
- 2ndswing.com TaylorMade 2024 P7CB Iron Set specification table — loft, lie, length and swing weight for the 3-iron through gap wedge, plus the Dynamic Gold Mid 115 stock shaft and the 4-PW stock make-up.
- todays-golfer.com 'Not your typical tour forging: TaylorMade P7CB iron review' and taylormadegolf.com product copy — the Compact Grain Forging process, the 1025 carbon steel, the milled face and grooves, the co-forged tungsten and the constant centre of gravity.
- Note: offset and bounce were not published in the sources consulted and are omitted rather than estimated. A separate independent database lists P7CB lofts one degree stronger in the 6, 8 and 9 irons and describes its own figures as approximate; the manufacturer-matching 2ndswing table is used here.
Last reviewed 2026-07-28. Spot an error? [email protected]